Sweep & inspection
Caps & crowns
Flue relining
Masonry repair
Gas fireplace serviceLevel 1 sweep and inspection to the NFPA 211 annual standard - flue, crown, cap, and flashing checked and photographed
Chimney sweep logs do not sweep chimneys. They loosen some creosote - which then falls where a brush and vacuum still have to collect it.
Trusted Chimney Cap & Crown for West Hills Homeowners
A missing or rusted-out cap is the quiet reason so many West Hills chimneys end up with water-stained fireboxes, cracked crowns, and birds nesting in the flue. The cap and crown are the two parts that take the weather so the rest of the chimney doesn’t have to.
Our technicians have up to 9 years of experience installing and repairing caps and crowns across the west San Fernando Valley, and we use the same professional-grade materials chimney pros specify – Gelco and Olympia Chimney among them – not the flimsy hardware-store covers that fail within a few seasons. We can often take on a straightforward cap or crown job the same day, and every visit starts with a camera inspection and a photo report so you can see exactly what’s wrong before anyone quotes a repair. Call (855) 337-1817 to book.
What Our Chimney Cap & Crown Service Includes
Cap and crown work is one of the five core services we offer at Chimney Sweep West Hills, handled by the same trained technicians who inspect and clean chimneys. No handoff, no separate contractor for the top of the chimney and another for the flue. Here’s what each piece of the work actually involves.
Cap Installation
A chimney cap is the lid that sits over the flue opening, held on by legs or a full surround, and it’s the single cheapest piece of protection you can add to a masonry chimney in West Hills. You need one if the flue is open to the sky, which lets rain straight into the firebox and lets birds, squirrels and debris settle on top of the damper. We fit a correctly sized single-flue or multi-flue cap with stainless or galvanized mesh, seat it so it doesn’t rattle in wind, and check that the mesh gauge will actually hold up to the heat and weather here rather than rusting through in a couple of seasons.

Cap Replacement
A cap that’s rusted, bent, missing mesh, or sitting crooked has stopped doing its job even though it’s still bolted on. Replacement is usually the right call once the mesh is torn or the top plate has corroded, because a cap with holes in it is no better than no cap at all. We pull the old unit, check the flue tile and crown underneath for damage the failed cap allowed, and fit a replacement sized to the actual flue dimensions rather than whatever’s closest on a shelf.

Crown Repair
The crown is the sloped concrete or mortar cap at the very top of the masonry, and its whole purpose is to shed water away from the brick below. When it cracks – and in the Valley’s hot, dry summers followed by winter rain, cracking is common – water runs into the chimney body, freezes nothing but soaks everything, and eventually shows up as efflorescence, spalling brick, or a damp firebox. We repair crowns with a properly bonded mortar mix, rebuild badly failed crowns where needed, and make sure the slope actually drains away from the flue instead of pooling at the center.

Crown Coating
Crown coating is a flexible, weather-resistant membrane applied over a crown that’s sound but showing surface cracks and wear. It’s the right option when the crown structure is intact and you want to stop hairline cracking from spreading before a small repair becomes a rebuild. We prep the surface, fill the defects, and apply a coating that moves with the crown instead of cracking away from it – a step that buys years of life on a crown that’s still doing its job.
Multi-Flue Cap
A multi-flue cap is a single larger unit that covers two or more flue openings on one chimney, common on West Hills homes with a fireplace plus a furnace or water heater venting through the same stack. You need one when separate caps per flue leave gaps or look uneven, or when a shared chimney has been leaking between the flues. We measure the whole stack, build the cap to cover every opening with proper clearance, and make sure each flue still draws correctly with the surround in place.
Custom Cap
Some chimneys don’t fit any standard size – oversized flues, unusual shapes, stacks with a steep crown, or a look the homeowner wants matched to the house. A custom cap is fabricated to the exact dimensions of that chimney so it seals properly and doesn’t look like an afterthought bolted to the roof. We take measurements on site, account for the flue arrangement and wind exposure, and fit a unit built specifically for that stack rather than forcing a stock size to work.
Styles & brands we work with
- Sweep & inspection
- Caps & crowns
- Flue relining
- Masonry repair
- Gas fireplace service
Brands We Service for Chimney Cap & Crown
We work with a short list of brands that chimney professionals actually specify, and knowing how each one wears is part of getting a cap or crown right the first time. Gelco crown and cap materials behave differently under the Valley sun than a basic mortar mix, and we know where those products need extra attention on a west-facing stack that gets baked all afternoon. Olympia Chimney caps and components are built to tighter tolerances, so a correct fit matters more – we size them to the flue rather than trimming them to fit after the fact. When a chimney’s liner is also worn, we can bring in HeatShield for resurfacing rather than jumping straight to tear-out, because the cap and crown decision often overlaps with what’s happening inside the flue.
Whether you already have one of these brands on the chimney, need a replacement, or have a cap of unknown make that’s failed, we can help. We service what’s there, tell you plainly whether it can be repaired or should be replaced, and back the recommendation with photos from the inspection. No upselling, no guesswork.
Signs You Need Chimney Cap & Crown Right Now
- Water in the firebox after rain. If you’re finding damp ash, rust on the damper, or a water stain on the firebrick after a storm, the cap or crown isn’t shedding water the way it should. Left alone, that moisture works into the masonry and the flue lining, and repairs get considerably bigger.
- Cracked or crumbling crown. Visible cracks across the concrete top, pieces flaking off, or a crown that’s pulling away from the flue tile all mean water is getting into the chimney body. A crown repair now is a fraction of what rebuilding the top of the chimney costs later.
- Birds, squirrels, or debris in the flue. An open or torn cap is an open door for nesting animals and leaves, and a blocked flue sends carbon monoxide back into the house instead of up the chimney. If you hear scratching or the fireplace won’t draw, get the cap checked before you light another fire.
- Rust, bent mesh, or a loose cap. A cap that wobbles in wind, has rust holes through the top, or lost its spark arrestor mesh has stopped protecting the flue. Valley wind and sun wear these units down steadily, and a replacement is a quick fix once it’s spotted.
- White staining or spalling on the brick below the crown. Efflorescence (the chalky white residue) and brick faces flaking off are signs moisture is moving through the masonry from the top down. That almost always traces back to a failed crown or a cap that’s letting rain in at the flue.
Our Chimney Cap & Crown Process – Step by Step
- 1
Inspection first. Before anyone quotes a cap or crown, we get on the roof and look – flue tiles, crown condition, flashing, and the cap itself. We run a camera down the flue to check the liner and photograph everything, so the recommendation is based on what’s actually there, not a guess from the ground.
- 2
Written findings and options. You get the photos and a plain explanation of what we found, plus the options: repair versus replace, coating versus rebuild, standard versus custom cap. If part of the work can safely wait, we’ll say so.
- 3
Material selection. We match the material to the chimney and the exposure – the right crown mix for a sun-baked stack, the right cap gauge and mesh for the flue size and local debris. Brands like Gelco and Olympia Chimney are specified where they’re the right fit, not as a default upsell.
- 4
The work itself. Old cap removed, crown prepped and repaired or rebuilt with proper slope, new cap fitted and sealed. We protect the roof and flashing while we’re up there and clean up after – no mortar left on the shingles.
- 5
Final check and photo record. We confirm the cap sits level, the crown drains correctly, and the flue still draws as it should, then hand you the before-and-after photos. You’ll know exactly what was done and have a record for your own files.
See the difference
Before
After
Before
After
Before
AfterHow Much Does Chimney Cap & Crown Cost in West Hills?
A typical chimney cap installation in West Hills runs $180 – $450 depending on flue size and whether it’s a single-flue or multi-flue unit, and a crown repair generally lands between $350 and $850 depending on how much of the crown has failed. A full crown rebuild on a badly deteriorated stack can run higher. Crown coating, which protects a sound crown before cracks spread, is usually the least expensive option of the three. Custom caps cost more than stock sizes because they’re fabricated to measure.
What moves the price: the number of flues, the size and shape of the chimney, whether the crown is repairable or needs rebuilding, and whether the job reveals a liner problem underneath. The way to avoid overpaying is to insist on photos of the actual damage before you approve anything – which is exactly what our inspection provides. Every estimate is free, the price is set per job in writing before we start, and the written estimate is the final word – no surprises added on the day.
Chimney Cap & Crown Near West Hills – Our Service Area
We handle chimney cap & crown work throughout West Hills and the surrounding communities, including Canoga Park, Woodland Hills, Winnetka, Reseda, Chatsworth, Porter Ranch, Bell Canyon, Calabasas, and Santa Susana. If you’re over in chimney cap & crown, we cover that too. Dispatch runs Sunday through Friday, 7am to 7pm, and most jobs in the immediate area get scheduled quickly. Call to check availability for your address.
Serving West Hills, CA – Our Local Coverage Area
We serve West Hills and nearby communities. Use the map below to see the area we cover. If you’re nearby, we can almost certainly help.
Frequently Asked Questions – Chimney Cap & Crown in West Hills
A chimney cap is the lid over the flue opening that keeps rain, animals, and debris out; the crown is the sloped concrete top of the masonry that sheds water away from the brick. Together they’re the chimney’s first line of defense against water damage, which is the leading cause of expensive chimney repairs. If either one fails, moisture gets into the flue and masonry, and the repair bill grows from there. We inspect both as part of every cap and crown visit.
Most cap installations and crown repairs are completed in a single visit, typically a few hours depending on the size of the chimney and the extent of the crown damage. A full crown rebuild or a custom cap that needs fabrication takes longer, and we’ll give you a realistic timeline in the written estimate. Multi-flue jobs run longer than single-flue ones. Call (855) 337-1817 and we’ll talk through your chimney specifically.
Figure roughly $180 – $450 for a standard cap installation and $350 – $850 for a crown repair, with custom caps and full crown rebuilds running higher. The exact figure depends on flue count, cap size, and how much of the crown has failed. Inspection and estimate are free, and the written estimate sets the final price. Call (855) 337-1817 for an exact quote – estimates are free.
Yes – we work with Olympia Chimney and Gelco cap and crown materials and know where each one tends to wear in this climate. Whether your existing cap is one of those brands, needs a replacement, or is an unknown make, we can assess it and recommend the right fix. We service what’s on the chimney and don’t push a brand you don’t need.
Same-day service is often possible for straightforward cap and crown jobs, depending on the schedule that day. We answer 24/7, and dispatch runs Sunday through Friday, 7am to 7pm; we’re closed Saturday. A call outside dispatch hours is booked into the next opening. Call (855) 337-1817 to check availability.
We stand behind the work we do and will address any issue with the installation. Specific warranty terms depend on the materials and the scope of the job, so we go over them with you as part of the written estimate rather than making a blanket promise up front. Ask us directly when we’re on site and we’ll be clear about what’s covered.
Clear access to the fireplace and the area around the chimney, and make sure we can get to the roof safely – trim any branches or clear anything blocking the way up. If you’ve noticed water stains, drafts, or animals, tell us when you book so we bring the right equipment. Aside from that, there’s nothing you need to do; the inspection and photo report are handled on our end. Call (855) 337-1817 to schedule.
Schedule Your Chimney Cap & Crown Service in West Hills Today
A failed cap or crown is one of the cheaper chimney problems to fix and one of the more expensive ones to ignore. We’ll inspect, show you the photos, and quote a written price before any work begins – no obligation, no pressure. Call (855) 337-1817. We answer 24/7. Fast dispatch from 7am to 7pm, Sunday through Friday.
Written by the team at Chimney Sweep West Hills.